Additional information
Brand Name | TONIFISHI |
---|---|
Origin | Mainland China |
Certification | NONE |
57.50 $
173 in stock
Brand Name | TONIFISHI |
---|---|
Origin | Mainland China |
Certification | NONE |
Purchase control panel, send matching dial set, wiring terminal 2!
Control panel features
1, size 77mm x 50mm, large board, compatible with 41A and 100A SCR
2, can adjust the spot welding time and spot welding current, range 0.02-1s, current 40-100, positive left button adjust time, right knob adjust current. For safety reasons, adjust the current knob for customization
Plastic handle potentiometer
This potentiometer, torque.
3, the foot switch wiring is isolated from the city electricity, even if the touch is safe
4, foot switch down, no matter how long the time can only spot welding once, the second spot welding needs to loosen, re treads
5, to increase the anti shake circuit, to prevent the foot switch down when the switch contact jitter caused by mistake spot welding
6,
control board will be replaced with a bright LED indicator, turn on the red light, and when the light is green, this is normal
Please buyers know
7, our main components are imported components, not cheap domestic components, to ensure that the performance of the board more stable
8, our company uses large core components, not cheap, small core.
9, the board is too large, tin processing at the current, to ensure output
10, made into spot welder after use, does not affect the home, city electricity.
The thyristor on the control board is 41A, and can only be used in a single microwave transformer. The double transformer will cause excessive flow damage. The primary full load current shall be below 20A, and the maximum shall not exceed 25A.
Want to use dual transformers, the primary current is greater, the use of 100A SCR control panel. It is suggested that the maximum primary current should not exceed 40
A.
For what is the maximum pass current, the specific reasons are explained later!
Although many friends make it easy, I can't guarantee success for everyone. DIY failure is normal. I will send the board before transformer field testing, and strive to improve the success rate of making friends, but can not guarantee that every friend connected with the control panel are normal, can not guarantee the ideal spot welding production. Buy a board to be able to accept the failure of the ideological preparation, do not accept, say, just a few points on the test board is broken, and require return, after all, the board price is very low, and the courier fee is not low. Board is sold without warranty.
Time relay and AC contactor scheme has the following obvious shortcomings: one is the wiring, wiring complex, the forum there are many advisory connection message; two is the time relay and AC contactor high price, lead to cost more; three is large, is not conducive to miniaturization; four is a big noise, pull the sound relay pops the big night is more obvious.
The board requires 9V transformer power supply shop need another photo, a few friends with their 12V powered unstable imagination! Therefore, the shopkeeper strongly recommended that all friends use the purchase of the 9V transformer. We are not responsible for any problems with the use of other power supplies. The transformer is not necessarily different from the batch as shown
Nameplate
Mind who do not shoot
In the use of two-way thyristor, in addition to ordinary SCR should pay attention to the problem, but also need to pay attention to the following points. for electronic enthusiasts to read for reference
1, the bidirectional thyristor is usually rated voltage, conduction current, trigger current, leakage current and voltage drop parameters, of which the first two in the application of the most important. For example, the control of lighting, lighting is not bright because the filament resistance is very small, light moment, impulse current to want 10, 20 times bigger than the current normal working hours, there is sufficient margin once chosen without pipe parameters, it is possible to make the big current impact and damage.
2. The average current given by the common thyristor in the parameter list or certificate is the average value, while the rated current given by the bidirectional thyristor is the effective value. Therefore, in the use of two-way thyristor instead of two parallel reverse common SCR, must be converted to select qualified components. The formula for conversion is IT=0.45IKs. Type: IT – ordinary SCR rated current safety; IKS – triac, rated current < <. For example, a bidirectional thyristor with an rated current of 500 is used as a bidirectional switch, which is equivalent to two ordinary silicon controlled rectifier with the number of current rating values,
IT=0.45×500 ANN =225 ANN
From an ordinary thyristor parameter series, the approximate value is 200, ann. Therefore, when the rated current is 500, the bidirectional thyristor can replace the ordinary silicon controlled rectifier with the current rating of 200 when used as an AC two-way switch.
3, the actual use, in the choice of triac triggering circuit, on the one hand should try to use more easily trigger the trigger trigger signal, on the other hand should trigger the signal voltage and current as high as possible and larger The The trigger current should normally be about twice as large as the Ic value found in the manual.
4, select the two-way thyristor, should choose the rated current value is greater than the load current RMS triac. For capacitive loads should also pay attention to over current protection.
5, for inductive load, it should be noted that the voltage rise rate is less than the du value given in the manual, otherwise there will be out of control phenomenon. To solve this problem, the RC electrode can be parallel in the RC circuit, the value of resistance R can be selected in about 100 ohms, the capacity of the capacitor C can be used for about 0.1 emblem.
6, pay attention to heat problems. Two-way thyristor and ordinary transistors, like a great impact on the temperature, the temperature is too high will be prone to malfunction, or even burn the device. Installation should be installed enough large radiator; in practical application to pay attention to the problem.
7, when the maintenance of electrical appliances need to buy a new two-way thyristor to replace has been damaged, in advance should be based on the power of the load to verify the original tube pressure and rated conduction current, and determine the polarity of the new device electrode Consistent with the original.
Do a friend of the welder Please read the following carefully!
Spot welding principle
AC spot welding machine is the use of transformers will 220V industrial spot welding machine generally use 380V AC conversion to a lower voltage, lead through the electrode lead to the spot welding electrode, the use of electrode short circuit electrode contacts and weldment is very low Of the contact resistance, tentatively called the short circuit generated by the moment of high current ablation welds to produce nuggets to achieve the purpose of welding. Spot welding when the high current is the key to spot welding, the production of spot welding should be able to produce large current as the main line, followed by the majority of users feel trouble the length of the spot welding control.
1. Transformer selection is critical.
Spot welding is a large current welding, welding power consumption is also great, spot welding battery thin nickel belt when the power is 2KW, which requires a large output power transformer, with a small transformer is difficult to succeed. Integrated transformer size, restructuring costs and restructuring workload considerations, the proposed use of microwave transformers, it is sufficient to meet the occasional spot welding in the day.
2. Select the appropriate time and switch control mode.
Industrial use of the spot welding machine is almost without exception, the use of control thyristor conduction angle and conduction time to control the spot welding current strength and time, and can be precisely controlled to a single pulse, online DIY spot welding machine Most of the time is to use the relay to control the way the AC contactor, this approach too many shortcomings, do not recommend the use of this approach, the proposed use of thyristor.
3. Correctly know the spot welding current and time.
Spot welding when the solder joint temperature is high, will cause the solder near the metal oxidation, thus affecting the solder joint strength and material properties, the longer the spot welding the more serious oxidation, so the appropriate welding method is as short as possible under short current time, Spot welding time is generally not more than 0.5 seconds. Industrial spot welding machine current output capacity is very large, so according to different thickness of the welding consumables to choose the appropriate current to prevent the solder paste, splash. Microwave oven transformer to change the spot welding current output capacity is generally limited, the general function of the current should be set in the maximum current, to explore the maximum current under the shortest welding time; transformer secondary and welding line thick, then the secondary current Relatively large, then the current should be transferred to the spot when the spot welding is not obvious discoloration as well. Some users due to the selection of the transformer is not appropriate or secondary line smaller lead output current is small, spot welding difficult to extend the spot welding time to make up, I do not advocate this, or should work hard from the transformer.
4. The relationship between spot welding voltage and spot welding effect.
Spot welding is a high current melting, is the current impact of spot welding effect, as long as the spot welding current is enough on the line, and spot welding voltage is not directly related, but the spot welding secondary circuit resistance but affect the maximum spot welding current. The resistance in the spot welding circuit has the contact resistance of the contact part, the spot welding electrode, the welding lead wire and the secondary winding resistance. If the total resistance in the spot welding circuit is large, it is necessary to achieve the ideal spot welding current Level voltage, but the increase in the loss of the circuit, the performance of the heat from the obvious, the efficiency is reduced; if the circuit resistance is smaller on the secondary can use a lower voltage, so the heat is not obvious, high efficiency, so large-scale industry Spot welding of the secondary cross-sectional area is very large, very thick electrode lead, secondary voltage is relatively low, and some only 2V. Most of the enthusiasts in the DIY spot welding when the secondary found around 4 laps voltage slightly lower than 4V when the spot welding effect is not ideal, increase the lap to increase the voltage after the spot welding effect will be good, and mistakenly think that the secondary voltage Good, in fact, his transformer secondary line cross-sectional area is not enough or the electrode lead wire is too small reason, the ideal spot welding machine is the secondary voltage can be produced at a lower voltage enough to increase the secondary voltage will bring To the welding line and secondary serious fever of the shortcomings.
5. Have a psychological preparation for welding heat.
Spot welding when the energy is very high, the solder joint temperature is very high, welding electrode and welding fixture is copper, heat quickly, continuous spot welding welding parts of the heat is very obvious, and even hot, high current welding Lead and secondary coil heating is also very obvious, the transformer is in the overload state, the primary coil and the core heat is also fast, so a single microwave oven to do a small spot welding machine is not qualified for a long time continuous spot welding, which heat The most obvious is the welding site, will be hot to hold you forcing you to stop. Because the welding parts will be hot to the first can not be used, so the internal parts of the spot welding machine do not need to force the heat; spot welding control panel on the SCR light the most light, so I designed the control panel SCR does not add heat sink.
If you want a long time continuous spot welding, you must consider the heat of the components forced cooling, welding parts of the general water cooling, welding lead cross-sectional area to be large, but also need to pass through the water, the control panel SCR Switch to a larger current module and reliable cooling, the main transformer have to heat, of course, a microwave transformer can not be competent, so down trouble is not small, the cost is not low, which is the industrial high point welding machine high price reasons.
6. Spot welding electrode on the spot welding effect of a great impact.
Electrode is an important part of the welding circuit, it conveys the welding area to the current and pressure, to distort the surface of the weldment and welding part of the heat, and the workpiece positioning, clamping in place, the working end and adjacent areas will bear Large current density, compressive stress and temperature gradient, working conditions are very harsh. Electrode selection is often not the attention of enthusiasts, practice has proved that ordinary materials in the copper pure copper can barely use, brass, aluminum can not be used, often used, or buy a special welding electrode, spot welding stainless steel You can use chrome zirconium copper, spot welding nickel plate is best to use alumina copper, spot welding pieces need tungsten molybdenum electrode. Specific options can Baidu look, the Internet has a more detailed description.
7. Welding electrode pressure affect the spot welding effect.
Spot welding to the need to apply the appropriate pressure welding, reducing the tip of the electrode and the weldment, welding between the contact resistance, increase the welding current, improve the welding effect. The pressure is too small will produce splash, burn thin welding consumables, solder joints difficult to form an effective nugget; pressure caused by the joints at the junction and accelerated welding ablation. Industrial spot welding is the use of pneumatic pressure, the pressure size is better control, personal use is a manual use of the feeling, to spot welding less splash, solder joints are not recessed for the ideal state, need to hands-on experience.
modname=ckeditor type1 square 10 x 10 x 1.1mm type2 round diameter 10mm type3 square 15 x 15 x 1.1mm type4 round diameter 15mm type5 square 20 x 20 x 1.1mm type6 round diameter 20mm type7 square 25 x 25 x 1.1mm type8 round diameter 25mm type9 square 30 x 30 x 1.1mm type10 round diameter 30mm type11 square 50 x 50 x 1.1mm Product Index Model 405nmNarrow-band filter Parameter The center The center wavelength Bandwidth:50nmThe left and right Cut-off depth:OD2-OD3 Characteristics Through Color The mirror is silver white The size of According to the demand [...]
64.66 $ Add to cartFeatures: x brand new and high quality x Set the grounding clamp to complete the welding operation anywhere in a few seconds. x Equipment to speed up grounding work. x With copper tail with good welding stability. x With strong magnetism, large suction. Single absorbable weight 3KG. Specification: x Type: welding headwithout wire tail/with wire tail x Material: iron/ copper / insulation board x Disk diameter: 36 mm x Size:As picture show x Applicable Scope: mechanical repair Package Contents:1 x Welding Supportwithout wire tail/with wire tail Note: 1. The real color of the [...]
51.58 $ Add to cartx 100 brand new and high quality x Made of high quality material, durable and practical to use x Glass: 6#7# 1.6 aperture; 8#10# 2.4 aperture; 12# 3.2 aperture x Easy to assemble and use. x For WP-17 / 18/26 TIG welding torch x Color: As pictures show x Quantity: 31 31pcs Set TIG Torch Accessories Note: 1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness. 2.Please allow slight manual measurement deviation for [...]
75.98 $ Add to cartSpecification: Brand new Color: as shown in picture High quality welding accessories for your welding work. Less gas consumption & gas turbulence, longer life of the tungsten electrode and lighter weld seams thanks to the gas lenses. Best ignition properties in TIG welding. Easy to use. Durable and practical. Package included: 5 x Gas Nozzles 4, 5, 6, 7, 8 4 x Adapter Sleeves 1.6 & 2.4 2 x Gas Lenses 1.6 & 2.4 1 x Isolator 1 x Short Burner Cap 1 x Long Burner Cap Note: Please allow a little errors due to manual measurement. Item color displayed [...]
56.83 $ Add to cartProduct Description: High energy efficiency: the honeycomb mesh cover makes the flame stable and improves the combustion load. 3,500 W Camping Gas Cooker works quickly to boil 1 litre of water in 3 minutes.Easy to ignite: This camping stove has a piezoelectronic ignition; the valve with the built-in, thickened sealing ring does not leak. With the built-in flame control knob, you can adjust the flame as needed.Strong air tank compatibility: Equipped with 2 types of connectors, perfect for different gas tanks. The seal of this adapter is very good, and closes automatically when not connected to the [...]
60.84 $ Add to cartMain Features: Kick stand pad helps to avoid motorcycle side stand scuff marks on ceramic tile. Prevents tip-overs caused by kickstands sinking into hot pavement or asphalt. Adds stability to your bike on grass,sand or soft ground – This kickstand rest even reduces scuffing on garage. Compact size fits easily in most pockets, tank bags, storage compartments, saddle bags, under seat, or just about anywhere. Wonderfully convenient! You rides and not worry about finding something to put under your kickstand when [...]
42.58 $ Add to cartFeatures -Made from 1.5cm or 2/3 inch thickened billet aluminum with unquestioned quality, lightweight and durable. Provides you nothing less than dynamic and exciting riding experience. -Processed by anodic oxidation, which translates to smooth and rust-resistant surface for enhanced visual impact. Available in black and blue, complement the custom look of Yamaha -Machined by cutting-edge CNC technology, accuracy of each cutting part can be ensured for easy installation. -Minimalism design, install right into the existing mounting locations and folds up underneath side panel when not in use Established in 2010, NiceCNC is a world's leading brand focused on a huge [...]
280.05 $ Add to cartSpecification: Product Details: -- Condition: 100 Brand New -- Color: -- Material: CNC Aluminum -- High quality CNC-machined billet 6061 aluminum -- Anodized coating -- Item is easy to install without instruction Package Included: 1 x Foot Kickstand Side Stand Enlarger Plate Extension Pad Fitment: For Haojue USR125 For Suzuki UU125 UY125T Feature: 1: With this larger stand foot, your bike always has a secure footing, even on soft ground, muddy verges, sand, soft asphalt and uneven surfaces. 2: It looks absolutely stunning, enhances the looks of your motorcycle. 3: With Best Anodized Finishing. 4: Installation Instructions Not Included. [...]
59.70 $ Add to cartProduct Features: The Kickstand Side Stand Enlarger Can Increase the Contact Area of the Kickstand and the Ground, Increase Friction, so that the Motorbike Parks More Stably Condition: 100 Brand New Material: CNC Aluminum Color : Quantity : 1Piece High quality and Easy installation Fitment: FOR KAWASAKI VERSYS 1000 SE 2019-2021 Please Ensure This Part Fits For Your Motorcycle Before [...]
53.49 $ Add to cartChcę coś kupić ale szukam informacji jak zamówić... |
Kupiłem coś ale chcę poznać status zamówienia... |
Odebrałem paczkę ale mam pytanie lub problem... |
Chcę dokonać zwrotu i potrzebuję informacji... |
Droptech Sp. z o.o. droptech.polska@gmail.com |
ul. Łódzka 118, Piotrków Tryb. Sprzedajemy tylko przez internet |
NIP: 7712911090 REGON 386758083 |
Wysyłka bezpośrednio od producenta lub dostawcy |
DARMOWA WYSYŁKA + ubezpiecznie dostawy + śledzenie przesyłki |
CAŁKOWITY ZWROT podczas reklamacji |
Reviews
There are no reviews yet.